Page 1 of 2
Re: A theory of a possible method of fusion
Posted: Sun May 27, 2018 3:38 pm
by Richard Hull
We humans are big bags of water.... we are water logged meat engines. The micro wave oven frequency was tuned for cooking wet meat and other water loaded food substances. Our bodies like to fully absorb 2.45 Ghz RF energy and fast neutrons. Your health, your choce!
Richard Hull
Re: A theory of a possible method of fusion
Posted: Sun May 27, 2018 6:38 pm
by steventw
Guess I’ll stick with the 2 copper wires
Thanks for advice
Re: A theory of a possible method of fusion
Posted: Tue Jul 10, 2018 6:19 pm
by steventw
Just in case missed post in contsrructor thread
Ok my idea that I’ve worked with I’ve simplified a little
For proof of concept I’ll be using 2 rows of magnets
Roughly 10 each side with like poles facing centre so that there pushin away
From what I’ve seen in vids on YouTube is plasma spinning around magnets so idea is to give it a run up or hopefully sling shot around as it moves down row of magnets toward centre
Videos I looked at for magnets plasma that came up in YouTube search
https://youtu.be/2B-lKgcQJvg
And
https://youtu.be/uPU9cEK5YsM
If magnets rows fixed down and are facing the like poles / repelling Poles
Plasma spinning from one row would be spinning opposite direction to other row and hopefully meet somewhere in middle
- FA764497-C969-4E0D-88D7-31C54A0BC79D.jpeg (35.64 KiB) Viewed 26908 times
If plasma gets a speed boost from spinning around magents on lead up
Might lower power requirements for fusion
If all works as theorised when build proof will upgrade proof to a prototype with rows on all 6 sides of square
- 8F148BFD-456E-4F4B-9560-F9C5CAEEF944.jpeg (33.57 KiB) Viewed 26908 times
From Steven Whittam
Re: A theory of a possible method of fusion
Posted: Mon Aug 13, 2018 1:18 am
by steventw
Well built my idea
Finished off today
Gona give it a test run with some argon cause have in hand at work
Today put the 4 copper grids 2 at base of each row to create plasma
Will try get a vid of it running later on
Re: A theory of a possible method of fusion
Posted: Mon Aug 13, 2018 4:33 pm
by steventw
Don’t think power supply I got was not sufficient enough for creating plasma with method using
Any suggestions as to what I could get that would be sufficient
Or maybe an easier way to create the plasma
Open to suggestions
Re: A theory of a possible method of fusion
Posted: Tue Aug 14, 2018 9:25 am
by Dennis P Brown
Rather difficult to make any suggestions what-so-ever when the only picture you show for the experiment is an open box held together with plastic straps.
Making a plasma is trivial if one uses a vacuum (say 50 milli-torr) and a few hundred volts even at a a few milli-amps.
If you are trying to create a plasma in air, you will need a very high voltage and the ability to 'strike' an arc. Look at the "Jacob's Ladder" demo's on youtube.
Re: A theory of a possible method of fusion
Posted: Tue Aug 14, 2018 11:42 am
by steventw
It’s an aluminium frame with bolts holding magnets
Ignore the zip ties they where prepairing to hold the copper wires
My
Older bro recommended usen one of the tig welders at work as a power supply
Got vacuum down to -25psi and added some argon gas
Tho only had some wires a few mm appart to test if could get an arch which it did.
Will be installing the copper grids hopefully tomorrow in hope to get some plasma flowing
Re: A theory of a possible method of fusion
Posted: Tue Aug 14, 2018 12:46 pm
by Dennis P Brown
OK; while the old negative pressure is still used on some ancient dial gauges or maybe AC units, might want to use positive readings; also, not inches. Maybe just convert to torr or pascal. That will mean more to others here.
Re: A theory of a possible method of fusion
Posted: Tue Dec 06, 2022 11:12 am
by steventw
Got a digital scale since then 2 in fact
One for pipe on pump and one for top of chamber
Made some bowl magnets
But got issues with leaks again
Took off diffusion pump and connected chamber directly to pump
Got similar pressures to with diffusion pump
But best I think was with about 150 micron on pump and about 190 on chamber , tho outa diffusion pump oil
I’ll throw some pics
Re: A theory of a possible method of fusion
Posted: Thu Dec 08, 2022 10:18 am
by Rich Feldman
Steve's back! Applause for plasma pictures.
A picture or description of whole vacuum apparatus could facilitate getting useful advice about reducing the pressure.
Re: A theory of a possible method of fusion
Posted: Sat Dec 10, 2022 1:57 pm
by steventw
I know where leak is
Just getting right attachment for chamber to diffusion pump
64mm tri clamp to kf50
Hard to get seal right give slight diff o-rings